Honda Civic Forums banner

1 - 20 of 25 Posts

·
Registered
Joined
·
37 Posts
Discussion Starter #1
I bought this recently, I know a guy built it from a forum some where! few issuses needed sorting and bits still need doing! on going project! Spanked my civic that was ready for paint after £200 of arch welding :( , long story. Anyway new one what you think?
 

Attachments

·
Registered
Joined
·
943 Posts
looks good from what i can see, this isnt project emo from csc is it?
 

·
Registered
Joined
·
340 Posts
it aint project emo, no offence to kingy at all but it think streaky would go mad if he read that lol

looks good mate, i guess that will be the track car that you joined the forums to find? GL with it!!
 

·
Registered
Joined
·
37 Posts
Discussion Starter #8
its not project emo but it does have streaky on the number plate anyone know? It has quite a bit already done:
Engine:
-B16A2 engine conversion with brand new cam belt fitted (800 miles ago) and EG VTI radiator same time ago, and new engine oil, gear box oil and Hamp filter, new dizzy fitted also at same time
-M Factory oil cooler kit with oil filter relocation
-BMC CDA cold air intake
-EK9 manifold (2.5inch collector)
-EK9 JDM Cat (2.5inch)
-5Zigen cat back exhaust system (2.5inch again with 3inch tip)
-Samco red silicone radiator hoses
-DC2 Teg steering rack with Chris G Special power steering removal kit
- BMA CDA Air Filter

Handling:
-Jamex shocks and Koni 30mm lowering springs
-DC2 teg front upper strut brace
-DC2 teg front subframe brace
-Cusco front lower brace
-Unbranded rear upper brace
-Beaks rear lower brace
-DC2 teg front anti roll bar
-VTi rear anti roll bar

Brakes:
-282mm "big brake" conversion using Prelude callipers
-282mm 4 X 100 PCD AP Dixcel FCR vented carbon brake discs )
-AP Dixcel Type Z carbon front pads to go with the front discs (put the discs and pads on at the same time as engine conversion 800 miles ago)
-Rear disc brake conversion consisting of VTi rear trailing arms running
-Mintex dimple and grooved discs and Mintex pads
-DC2 Teg 1inch master brake cylinder and servo

Interior:
Momo Race steering wheel
-3 guages in pods displaying oil temp, oil pressure, and currently not connected water temp but lights up along with the rest
-Recaro recliner bucket seat
-Cobra recliner bucket seat


Exterior:
-Vented carbon fibre bonnet, don't know what make, but is light weight
-12 Tune Spoon carbon fibre spoiler
-racing reference 2 piece split alloys
-Black indicator
-Half tinted rear lights
-JDM Wind Deflectors
 

·
Registered
Joined
·
37 Posts
Discussion Starter #11
Like i said its a nice spec but it needs a few bits finishing and sorting out mainly the infernal squeaking! I know its got braces n stuff everywhere so that could have some thing to do with it. Ill find out eventually!anyway nearly all my b18 rebuild stuff is here from the states waiting on headgasket and valve stem oil seals. Looking for a lightened flywheel and clutch for it at the min and light under drive pulley. pics will follow when i get a decent camera! just pics i got of the advert when i bought it. ;)
 

·
Registered
Joined
·
32 Posts
I know this car very well (sounds dodgy lol)...its my b/f's brothers old car aka streaky, funnily enough it also turned up on the Rebel forum and I have been on a run with it in Wales with the guy I guess you bought it from 8-|
 

·
Registered
Joined
·
37 Posts
Discussion Starter #17
At last someone knows who built it! thanks for the other pics as well. What was it like when he had it? running wise etc...
Thanks lottie. :)
 

·
Registered
Joined
·
37 Posts
Discussion Starter #19
cool! it seems pretty good in fairness. just niggles! Think im too picky sometimes. anyway ill post up the work im doing soon. B18c had a steam clean on friday, looks nice! thanks again
 
1 - 20 of 25 Posts
Top